MYPIN TA4 PID Controller, The MYPIN TA4 PID is one of the better controllers from China. Here is a copy of the actual instructions that ship with the controller . JConn Inv. PID Controller Instruction Manual This information is specific to the Mypin TA4 based controller sold by JConn Inv. but it should work for most TA4. Anyway, the manual did not come with the MYPIN PID. Does anyone have a link to the MYPIN PID manual? Manual for Mypin TA4.
|Published (Last):||12 December 2012|
|PDF File Size:||13.78 Mb|
|ePub File Size:||3.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
Your name or email address: Apr 10, 9. The PID is now in manuap tune mode 4. Mypin autotuning is covered in my assembly mypin ta4 manual. The C in the lower display will start flashing 5. Apr 9, 1. Apr 9, 3. Apr 9, 7. Keep in mind that the best auto tune would be one that simulates smoking conditions as closely as possible. mypin ta4 manual
Apr 10, Good luck with you smoking. I think it is in the PID setup. I have read on line lots but still can’t mwnual get the idea in my head. Press the green UP mypin ta4 manual and the display will change to flashing F 6. You are not logged in. Idea of just unplugging and plugging in seemed little harsh for length of use. At4 that I am aware of.
Then a different style of probe might work. mypin ta4 manual
MyPin TA4 set-up
Next issue not sure if it is a issue but I did mypin ta4 manual mpin water trick for probe caliberation. I’m a chatter box today lol just trying to get it dialed in. In my ice water after letting ice sit in there three minutes and 1 stir. Are you using a Filastruder mypin ta4 manual a flamethrower? Apr 9, 4.
Setting your controller temperature. Only concern I have which may go back to what dward said is mypin ta4 manual I et the temp to 52 degrees and my basement is reading RSS topic feed ,anual Brandon, I just received your PM and sent you a reply.
Yes mine did the same. Press “set” until “HYS” 6.
Press “set” until “P” 3. That is why you will see some pulsing of the power as a properly tuned PID works.
Ta4 Wiring Diagram
Homebrew kegging tw4 draft beer tapping equipment including aluminum CO2 tanks, CO2 regulators, quick disconnects, Cornelius kegs, beer taps, mypin ta4 manual taps, beer hardware, hoses and fittings. You can put mypin ta4 manual few bricks on the rack of manuwl smoker to simulate the meat as the bricks will soak up some of the heat similar to the way meat will. That’s for the myPIN controller. For the sake of flawless product as possible o kind of want to change it.
Press and hold “set” button for 3 seconds. Programmed it according to the heat recommendation. I mypin ta4 manual that parameter p in the pid programming from I think I had 8. Anyway to negate that or is it worth worrying about? You must log in or sign up to reply here. Hold down mypin ta4 manual SET button until the top display displays the temperature. Thanks fellas for the information, yes it is coming together a little more and more mypin ta4 manual and there l.
That works for me. The whole auto tune thing I’m not sure on doing yet, I’ve read people have better results setting it manually. What you saw is normal. I think the “P” parameter mypin ta4 manual be “off” and the “hys” parameter set to “5”. Also the reason the temp goes up quickly when you grab the probe is your body temp is much higher than the air temp, so it climbs rapidly.
If you were to stick it into a glass of room temp water, it would drop fairly rapidly. Thanks, but I was hoping for an operations manual. Here is the link to the Sestos manual and spec sheet.
Can anyone explain what the p value is and how its effecting the unit? How do I change the temperature I’d like to extrude? You have 2 choices. Here mypin ta4 manual a mypin ta4 manual of kanual actual instructions that ship with the controller: Fellas, good news since turning that p value to off I’m able to get the pid and ssr to communicate properly.
Then the AT light will turn off.